Cloning Designer Garments, couture sewing, Drafting Patterns, French Jackets, Uncategorized

Drafting the Three Piece Sleeve

I’ve written about this in the past but have revised the method slightly. I’ve seen converting the two piece sleeve to a three piece by simply splitting the upper sleeve at the shoulder point. This method results in a wide under sleeve. The classic Chanel design has a much narrower under sleeve section. I’ve found the easiest way is to convert the two piece pattern to a one piece sleeve; then split the sleeve.

First cut off the seam allowances from your pattern. Pattern drafting is always done with no seam allowances. You will add seam allowances after all drafting is completed. Extend the grain lines the full length of the pattern. If the elbow point isn’t indicated, measure your arm and determine your elbow point. Line up the upper and under sleeve patterns along the underarm line. Make sure the grain lines are parallel to each other. Trace the top of the sleeve from the underarm point on the under sleeve around to the front of the upper sleeve.

AC6699F9-1C3D-41C0-8FDD-4A37C6ADDF41

Shift the pattern to complete the top of the sleeve on the right side. Draw a horizontal line connecting the underarm points. Draw a horizontal line to indicate the elbow position; also draw the finished hem of the upper sleeve.

30ED97D8-F213-43C3-BF93-F652238E9FC0

BED09AFF-8BF0-4A58-A5DB-1850FD5736E0

EE1B8EFA-CEB5-40A2-8823-068B93DFBBC6Determine the midpoint of the underarm line (line which will divide the sleeve in half lengthwise). Extend this point to the bottom of the sleeve.

27BA9932-28A9-4ED0-8149-876A7C7355BE

Determine the finished width of the sleeve hem. Divide by 2. Mark 1/2 finished hem width on either side of center. Connect the underarm points to the points on the hem for side sleeve shaping.

ABAD0B7F-C902-47C2-AA56-D982D4A8ABAB

Shift the midpoint of the sleeve about 1/2 inch towards the right (front of sleeve). Extend this point up to meet the top of the sleeve. This moves the shoulder point, also known as the pitch point, a little further to the front and places the finished sleeve more in line with the natural position of the arm.

C9E1E0B7-DF4E-4029-B3F8-154974B7AC97

Fold the left (back of sleeve) underarm point to meet the just marked offset center point. Trace the armseye seam from the side seam to fold.

CDDF71B2-DD46-42DD-8632-2AFEEF46BEED

When you unfold the paper, it should look like this:

59C1B69D-4D86-43EF-9487-35E2A70CA92F

Repeat for the right (front side). Fold the right underarm point to meet in the center and trace. You should have the underarm curve duplicated in the center of the sleeve.

436B06DB-54A9-4F09-8D59-60AD3F0BCAF0

Draw a horizontal line indicating the elbow line. If the elbow isn’t indicated on the original pattern, measure your arm either from the underarm or shoulder. Cut the pattern from the back side seam to sleeve center. Cut the pattern from the hem along the center to just before the elbow line, leaving a small hinge point of paper. Rotate the paper to open up a dart along the elbow line. The dart should be about 3/4 inch wide. Tape extra paper underneath the opened dart. Tape the overlapping pattern at the hem. The width of the sleeve hem will be shorter due to the overlap. Measure the amount of overlap and add that amount to the right (front) sleeve at the hem. Extend up to meet the elbow line.

E60D861E-E510-484D-8262-7A2B95DABB45

Draw an elbow dart 3 inches long and 3/4 inch wide (the amount the paper was opened). There will be extra fabric, indicated in green. This is to provide ease over the elbow. The angle between the sleeve midline above the elbow and sleeve midline below the elbow will be about 175 degrees. A little more or less is fine.

The undersleeve on classic Chanel jackets is about 2.5 inches wide at the underarm tapering to 2 inches at the wrist. This is for smaller sizes; you may want to adjust for larger sizes/ fuller bicep. From the center line, measure towards the sleeve back 1 and 3/8 at underarm, 1 and 1/4 at elbow and 1 and 1/8 at wrist. For the front, measure from center towards sleeve front 1 and 1/8 at underarm, 1 and 1/8 at elbow and 7/8 at wrist. Connect the points to form the undersleeve. Shown in red.

7F79F0BB-6FA0-4F9F-8B42-7EBD704DFC6D

Now remove the corresponding amounts from the side seams. Shown in blue. Trace the undersleeve onto pattern paper. I place the upper portion of the undersleeve on the bias. The lower portion won’t be on the true bias but it will be off grain. This will allow the undersleeve to stretch when worn for comfort. Chanel sleeves are intended to be slim fitting and the bias provides a little wearing ease. Trace the upper and lower sleeve sections. Your patterns should look like this:

22E5D9BB-0973-4656-BDE6-9EFCE493C117

Using the hem length from the original pattern adjust the bottom of the sleeve. The sleeve back which joins the undersleeve should be 1/2 to 3/4 inch longer than the corresponding seam along the undersleeve. The excess length in the back sleeve will be eased in the elbow area. The seam joining the sleeve back to sleeve front will be the same length on both back and front. The front sleeve seam which joins to the undersleeve should be 3/8 to 1/2 inch shorter than the undersleeve seam. The upper sleeve seam will be steamed and stretched before sewing to give the sleeve proper shape. The sleeve hem should be slightly longer in the back and angle upwards to the front. Add vent extensions for buttons if you want. The top of the sleeve cap can be curved to decrease the amount of fabric needing to be eased into the armseye.

EAD92312-CD88-4CC0-A400-5F1DF93D4C51

 

French Jackets

Chanel and the Sleeve

The past month has been occupied with a quest to develop a sleeve pattern for the French boucle jacket. Chanel was obsessed with sleeves. Axel Madsen writes in Chanel: A Woman of Her Own: “she would pin up a dress as many as twenty times to get it right. Armholes were her bane-and the engineering secret of her jackets.” Jackie Rodgers, a Boston-born mannequin, would recall: the armhole was never high enough, and she’d reset a sleeve six times. The high armhole gave the jacket the cleaner, closer fit she wanted.”

Also, just some interesting notes regarding us sewers referring to our projects as “Chanel jackets.” I’ve read that Chanel takes a dim view of this and states that “only Chanel can make a Chanel jacket.”  True but Coco had somewhat a different take on those who copied her work.  Axel Madsen also notes that: “Coco had always believed that any fashion not adopted by a majority of women was a flop. To see herself copied in the street was the greatest compliment. Piracy was the flattering result of success.”

We may not be able to make a “Chanel jacket” but Gabrielle Chanel would have been flattered by sewers devoting endless hours to emulate her work.

In order to avoid the “home sewn” look, you need to get the fit of your jacket perfected, especially the shoulders and sleeves. Too many jackets appear that are much too large through the shoulders. Most commercial patterns have sleeves which are much too wide and the whole effect of the chic jacket is lost.

The three piece sleeve seems to be the holy grail of Chanel jackets. I found almost nothing published on how to draft this sleeve and so began my quest.

This post will demonstrate my method of drafting a three piece sleeve from an existing two piece sleeve. Future posts will explore custom sleeve drafting and some radically different sleeve shapes.

First I’ll deal with the armseye shape. The scye, as it’s referred to in professional tailoring language, is the basis for beginning the sleeve draft. If your jacket has the wrong shape and size armhole, you have no chance of getting a correct sleeve fit. Perfect your muslin fit and make any changes necessary to the sleeve before proceeding. You will also need to remove all seam allowances from the pattern. All professional pattern drafting is done without seam allowances. If you try this process without removing the seam allowances, things will become muddled very quickly. Sorry to those who prefer to work with seams added.

The scye shape is easiest to visualize by laying the jacket body sections on a grid with the armhole seams just touching and all grain lines parallel.

image
Here is an example of a poorly shaped scye. It is too narrow, vertical and doesn’t follow the natural shape of the arm. The armhole is also too low. Much better drafts look look this:
scye 7975
Vogue 7975
Chanel scye
The scye from a Chanel ready to wear jacket.
Scye 8991
Vogue 8991
Scye shapes overlaid showing the small variations.
Scye Overlays

I’ll use Vogue 7975 as the example of how to draft a three piece sleeve. This is a pattern used by many as the basis for their Chanel style jacket. It also has a two piece sleeve, perfect for demonstrating how to transform it into the coveted three piece draft. The McCalls pattern shows what to avoid. It should also be clear from these diagrams that substuting one sleeve pattern for another can be risky. Imagine trying to get the sleeve from Vogue 7975 into the McCalls armhole. Sleeves are drafted to correspond to a specific armhole shape and size. You might get away with switching the Vogue sleeves but even that might require some tweaking.

The first step may appear counter-intuitive, but I found it easier to return the two piece draft to a one piece and then draft the three. Altering and combining the two piece into three created multiple issues and this approach worked better for me.

Start by aligning the grains and have the seams just touching. Remember, NO SEAM Allowances.

Tracing Sleeve 1

Tracing Sleeve 2
Trace the sleeve cap shape onto paper, either gridded or plain. Stop the tracing at the underarm match point on both front and back. You should now have a sleeve that looks like this. Don’t do anything with the lower sleeve yet; all you want is the shape and size of the armseye seam.
Tracing Sleeve 3
Connect the underarms with a straight line. From the shoulder match point drop a line straight down which intersects with the underarm line at right angles. Make it a few inches longer than the sleeve length. Measure and mark the sleeve length from the top of the sleeve cap to the hem. Mark back and front as its easy to get confused until you’ve done this a few times. The back will be slightly wider than the back. I’ve written 6 5/8 on the back and 6 3/8 on front.

Now mark A, B and C as shown. Cut along the sleeve cap line.

sleeve cap points
Fold point C directly on top of point B and trace the underarm seam.

underarm line 2
underarm line 1
Fold point A directly on top of B and trace the underarm seam.
You should now have this:
underarm line 3
Measure out along the underarm line 1 and 3/8 inch left of B. Measure 1 and 1/8 to right of B. You are starting to form the undersleeve piece.

Next you need to draw in the bottom of the sleeve. Measure the finished width of the sleeve hem. Size 8 measured 8 and 3/4 inches.  The line down the middle of the sleeve is offset 1/4 inch towards the sleeve front; 6 and 5/8 along back underarm, 6 and 3/8 along front underarm. Therefore you need to offset the hem by the same amount.

Sleeve hem measures 8 and 3/4, half of which is 4 and 3/8. Add 1/8 inch to back and subtract 1/8 inch from the front.  Your sleeve hem will measure 4 and 1/2 inches along back sleeve and 4 and 1/4 inches along front sleeve.
sleeve hem
The sleeve needs to bend at the elbow to follow the natural shape of the arm. Every drafting source I found used arbitrary values to establish this bend. After measuring countless arms and sleeves I decided what made more sense was to duplicate the angle. A perfectly straight arm would have a straight line from top to bottom. Most peoples’ arms bend at about 175 degrees with the elbow as the pivot point. The dress form with sleeve showing this angle.
elbow angle on form
A Chanel sleeve from a ready-to wear jacket showing this angle.
elbow angle on chanel
This shows a two piece sleeve but the angle remained remarkably consistent with everything I measured. Therefore, I decided to draft the lower sleeve to reflect this angle. Draw a horizontal line where the elbow bends. Measure from the top of the sleeve. This measurement isn’t critical so just get close but don’t go crazy trying to find the exact point. This is the elbow line.
elbow angle
elbow angle 4
This pushed the seam 3/4 inch towards the right. In order to maintain the width at the hem, the center line and front seam needed to be redrawn 3/4 inch towards the right. Come straight down from the sleeve top, pivot at the elbow and continue to the hem.

To finish the under sleeve pattern measure out along the elbow line 1 and 1/4 inch towards the sleeve back (left of center) and 1 and 1/8 inch towards the sleeve front (right).undersleeve 3
At the hem measure 1 and 1/8 inch towards back and 7/8 inch towards front. Connect the points from the underarm line through the elbow line and pivot to hem. Your undersleeve should look like this. It is is red.
In order to complete the back and front upper sleeve patterns, the width of the undersleeve needs to be subtracted from the upper sleeve pieces. Along the back seam, measure in 1 and 3/8 at the underarm, 1 and 1/4 at the elbow and 1 and 1/8 at the hem.
Along the front seam, measure in 1 and 1/8 at the underarm, 1 and 1/8 at the elbow and 7/8 at the hem. These lines are shown in green.
upper sleeve draft
Add ease to the back upper seam to allow the elbow to bend. Measure down 3/4 inch from the elbow line and form a dart about 3 inches long. This will be eased into the seam. The seam needs to lengthened by the same amount so lower the hemline 3/4 inch and angle upwards to the front seam.

elbow dart

 

angled hemTrace off the under sleeve, shown in red. Be sure to mark front and back. The upper sleeve is for the RIGHT sleeve, the under sleeve is for the LEFT sleeve. This pattern gets flipped for the right sleeve. Don’t get confused. That’s just the way this draft works.

lower sleeve final
Trim the upper sleeve pieces along the green lines and along the center line. They can look similar so be sure and label them before you cut apart. You can also trace them to save your master draft.
upper sleeve final
Final sleeve draft.
completed sleeve Next will be a mock up to test the fit and adding a working vent. This post took hours to write and I hope not too confusing. I am going a little buggy now and hope it makes sense. Please let me know if any steps need clarifying and I’ll address questions in the next post. This was a while coming but I think most of the glitches are worked out. Next is custom drafting the sleeve cap.